Krink Parts

22 of 22 Items
  • Lower Handguard Shim - Krink and M92 / M85

    Lower Handguard Shim - Krink and M92 / M85

    One laser cut shim. Fits inside your lower handguard retainer to tighten up fitment of loose furniture.These fit on: AKS-74u, all makes and calibers Arsenal SAM-7K Arsenal SLR-106U and UR Zastava M92 Zastava M85

    $2.99
    Add to Cart
  • Cheap Krink Handguard Set - Stamped Cheap Krink Handguard Set - Stamped Cheap Krink Handguard Set - Stamped Cheap Krink Handguard Set - Stamped

    Cheap Krink Handguard Set - Stamped

    Arsenal USA made AKS-74U handguard sets that have been crudely fitted.Each set includes one upper handguard, one lower handguard, and one shim which should allow you to tighten it back up.These are made to fit stamped receivers.

    $13.99
    Add to Cart
  • 4.5mm Side Folding Rear Trunnion, No Short Rivet Holes 4.5mm Side Folding Rear Trunnion, No Short Rivet Holes

    4.5mm Side Folding Rear Trunnion, No Short Rivet Holes

    The times of dealing with finicky 4.5mm rear trunnions are gone! These Chefur Custom reproductions are the easiest trunnions to build on. This version has no short rivet holes. For use on Childers, AK-Builder, or all other receivers with pre-drilled...

    $124.99
  • AK-74 Bullet Guide

    AK-74 Bullet Guide

    Fully heat treated, parkerized finish, ready to build on.The rivet hole is slightly undersized to allow match drilling with your trunnion. These are compatible with: Surplus AK-74 Tantal Kalashnikov USA These are NOT compatible with: Palmetto State...

    $39.99
    Add to Cart
  • Russian 4.5mm Triangle Folder Stock Russian 4.5mm Triangle Folder Stock Russian 4.5mm Triangle Folder Stock

    Russian 4.5mm Triangle Folder Stock

    These are genuine Russian military 4.5mm side folding stocks.These stocks are in used condition, expect surface wear and light rust. They are in fully servicable shape. A perfect match for my Triangle folder rear trunnions.  

    $149.99
  • AKS-74U Barrel, 23mm

    AKS-74U Barrel, 23mm

    Reproduction AKS-74U barrels made by AK-Builder. Chrome lined 5.45x39 Correct 1:6.3" twist rate 23mm chamber diameter AK-Builder makes their rear sight block journal oversized to accomodate all surplus blocks, which results in an overly tight fight...

    $189.99
  • AKS-74U Barrel, 22mm

    AKS-74U Barrel, 22mm

    Reproduction AKS-74U barrels made by AK-Builder. Chrome lined 5.45x39 Correct 1:6.3" twist rate 22mm chamber diameter AK-Builder makes their rear sight block journal oversized to accomodate all surplus blocks, which results in an overly tight fight...

    $189.99
  • AKS-74U Gas Piston, AKM Spec AKS-74U Gas Piston, AKM Spec

    AKS-74U Gas Piston, AKM Spec

    Heat treated on the inside and fully chrome plated on every outside surface, these gas pistons are the most faithful reproductions ever made! This listing is for a piston made to be used with an AKM or WBP 5.45/5.56 carrier.Please see this listing...

    $39.99
  • AKS-74U Gas Piston, AK-74 Spec AKS-74U Gas Piston, AK-74 Spec

    AKS-74U Gas Piston, AK-74 Spec

    Heat treated on the inside and fully chrome plated on every outside surface, these gas pistons are the most faithful reproductions ever made! This listing is for a piston made to the original Russian/Bulgarian specs, for use with a 5.45x39 AK-74 bolt...

    $39.99
  • AKS-74U Dust Cover Assembly AKS-74U Dust Cover Assembly AKS-74U Dust Cover Assembly

    AKS-74U Dust Cover Assembly

    The ever elusive original style Krink top cover is finally available! Compatible with all original parts and accessories, including picatinny and briefcase mounts Comes fully assembled with a rear sight installed Parkerized finish Made from surplus AKM...

    $164.99
  • AKS-74U Gas Tube AKS-74U Gas Tube

    AKS-74U Gas Tube

    Brand new reproduction gas tubes for the Krink! Made to original specs, compatible with all original parts Heat treated Parkerized finish Locking surfaces left oversized to virgin spec for proper fitting to your rifle

    $89.99
  • AKS-74U Booster Muzzle Device AKS-74U Booster Muzzle Device AKS-74U Booster Muzzle Device

    AKS-74U Booster Muzzle Device

    Brand new reproduction boosters for the Krink! Threaded standard 24x1.5mm, fits all original AKS-74Us Heat treated Chrome lined through the entire inside, including threads. Easier to remove after fouling than any others! Parkerized finish

    $74.99
  • 4.5mm Side Folding Rear Trunnion 4.5mm Side Folding Rear Trunnion

    4.5mm Side Folding Rear Trunnion

    The times of dealing with finicky 4.5mm rear trunnions are gone! These Chefur Custom reproductions are the easiest trunnions to build on. This version has all the rivet holes drilled. The rivet holes will line up with the receivers below. If you are...

    $124.99
  • 4mm Cross Pin for Rear Sight Block / Hinge Block

    4mm Cross Pin for Rear Sight Block / Hinge Block

    This is the cross pin that secures the rear sight block or hinge block onto the barrel on AKM rifles and their derivatives. These are made to the original Russian spec and are hardened.These will fit: AKM AK-74 and AKS-74u AK-100...

    $3.99
    Add to Cart
  • AKS-74u / Krink Plunger Spring

    AKS-74u / Krink Plunger Spring

    This is a spring for the Gas Tube Plunger on an AKS-74u.The fitment of these can vary. On some rifles, they will drop in. On other rifles you may need to trim 2-3 coils off to make the top cover close all the way. If you encounter any issues, please...

    $3.99
    Add to Cart
  • AKS-74u / Krink Gas Tube Plunger

    AKS-74u / Krink Gas Tube Plunger

    This is a Gas Tube Plunger for the AKS-74u. It rides inside the hinge block, and is pressed forward when you close the dust cover, securing the gas tube.Made to original Russian specs.

    $5.99
    Add to Cart
  • AKS-74u / Krink Dust Cover Pin

    AKS-74u / Krink Dust Cover Pin

    This is the pin used to install a Krink dust cover. Made to original Russian specs. You will need to flare both ends to secure the pin, much like a rivet. Most people accomplish this with two ball bearings on either side, being squished in a vise.

    $3.99
    Add to Cart
  • AKS-74u / Krink Hinge Block Hardware Only AKS-74u / Krink Hinge Block Hardware Only

    AKS-74u / Krink Hinge Block Hardware Only

    This is all the hardware you need to complete your Krink hinge block. This set includes: Cross pin for the dust coverGas tube lock plunger + spring4mm cross pin for securing the block to the barrel   This set will automatically be discounted...

    $14.99
  • AKS-74u / Krink Hinge Block AKS-74u / Krink Hinge Block AKS-74u / Krink Hinge Block

    AKS-74u / Krink Hinge Block

    Brand new reproduction hinge blocks for the AKS-74u. These are machined from 4140, heat treated, and come parkerized for protection.These are clones of a block from an original Bulgarian military AKS-74u kit. The press fit journal and outside width of...

    $135.99
    Add to Cart
  • AKS-74u / Krink Handguard Retainer AKS-74u / Krink Handguard Retainer

    AKS-74u / Krink Handguard Retainer

    Brand new reproduction handguard retainers for your AKS-74u build! These are machined from 4130 steel and heat treated to original specs, and come with a blued finish.These are sized to fit standard spec AKS-74u barrels. Fitment may vary with a...

    $94.99
    Add to Cart
22 of 22 Items
!

© 2024 Chefur Powered by BigCommerce All rights reserved. | Sitemap